 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Technical Data Sheet 0603 Package Infrared Chip LED SIR19-315/TR8 Features Small double-end package Peak wavelength p=870nm Package in 8mm tape on 7" diameter reel Compatible with infrared and vapor phase reflow solder process. Pb free RoHS refer to SMD B type SGS report Descriptions SIR19-315/TR8 is an infrared emitting diode in miniature SMD package which is molded in a water clear epoxy. The device is spectrally matched with silicon photodiode and phototransistor. Applications PCB mounted infrared sensor Infrared remote control units with high power requirement Scanner Infrared applied system Device Selection Guide LED Part No. SIR Chip Material AlGaAs Lens Color Water clear Everlight Electronics Co., Ltd. Device NoDTS-193-193 http:\\www.everlight.com Prepared date02-15-2006 Rev 1 Page: 1 of 9 Prepared byPosen Hsu SIR19-315/TR8 Package Dimensions Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions 0.1mm Absolute Maximum Ratings (Ta=25) Parameter Continuous Forward Current Reverse Voltage Operating Temperature Storage Temperature Soldering Temperature Power Dissipation at(or below) 25Free Air Temperature Symbol IF VR Topr Tstg Tsol Pd Rating 70 5 -25 ~ +85 -40 ~ +85 260 110 Units mA V mW Notes: * Soldering time5 seconds. Everlight Electronics Co., Ltd. Device NoDTS-193-193 http:\\www.everlight.com Prepared date02-15-2006 Rev 1 Page: 2 of 9 Prepared byPosen Hsu SIR19-315/TR8 Electro-Optical Characteristics (Ta=25) Parameter Radiant Intensity Peak Wavelength Spectral Bandwidth Forward Voltage Reverse Current View Angle Symbol Ie p VF IR 21/2 Condition IF=20mA IF=20mA IF=20mA IF=20mA VR=5V IF=20mA Min. 1.0 860 -1.20 --Typ. 1.3 870 45 1.35 -140 Max. -900 -1.70 10 -Units mW /sr nm nm V A deg Everlight Electronics Co., Ltd. Device NoDTS-193-193 http:\\www.everlight.com Prepared date02-15-2006 Rev 1 Page: 3 of 9 Prepared byPosen Hsu SIR19-315/TR8 Typical Electro-Optical Characteristics Curves Fig.1 Forward Current vs. Ambient Temperature 140 120 100 80 60 40 20 0 Fig.2 Spectral Distribution 100 80 60 40 20 0 IF=20mA Ta=25C -25 -20 0 20 40 60 80 100 810 830 850 870 890 910 930 950 970 Fig.3 Peak Emission Wavelength Ambient Temperature Fig.4 Forward Voltage vs. Ambient Temperature(C) 910 1.5 890 1.4 870 IF=20mA 1.3 850 830 -25 1.2 0 25 50 75 100 25 50 75 100 120 Everlight Electronics Co., Ltd. Device NoDTS-193-193 http:\\www.everlight.com Prepared date02-15-2006 Rev 1 Page: 4 of 9 Prepared byPosen Hsu SIR19-315/TR8 Typical Electro-Optical Characteristics Curves Fig.5 Relative Intensity vs. Ambient Temperature(C) Fig.6 Relative Radiant Intensity vs. Angular Displacement 2.0 -20 -10 0 10 20 30 1.5 IF=20mA 1.0 0.9 40 50 60 70 80 0.6 0.4 0.2 0 0.2 0.4 0.6 1.0 0.8 0.7 25 50 75 100 0 120 . Everlight Electronics Co., Ltd. Device NoDTS-193-193 http:\\www.everlight.com Prepared date02-15-2006 Rev 1 Page: 5 of 9 Prepared byPosen Hsu SIR19-315/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30 or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 605 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device NoDTS-193-193 http:\\www.everlight.com Prepared date02-15-2006 Rev 1 Page: 6 of 9 Prepared byPosen Hsu SIR19-315/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280 for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Everlight Electronics Co., Ltd. Device NoDTS-193-193 http:\\www.everlight.com Prepared date02-15-2006 Rev 1 Page: 7 of 9 Prepared byPosen Hsu SIR19-315/TR8 Package Dimensions Taping Dimensions Unit: mm Everlight Electronics Co., Ltd. Device NoDTS-193-193 http:\\www.everlight.com Prepared date02-15-2006 Rev 1 Page: 8 of 9 Prepared byPosen Hsu SIR19-315/TR8 Packing Quantity Specification 1.3000Pcs/1Volume1Volume/1Bag 2.10Boxes/1Carton Label Form Specification CPN: Customer's Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place RoHS SIR19-315/TR8 Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don't reproduce or cause anyone to reproduce them without EVERLIGHT's consent. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http:\\www.everlight.com Everlight Electronics Co., Ltd. Device NoDTS-193-193 http:\\www.everlight.com Prepared date02-15-2006 Rev 1 Page: 9 of 9 Prepared byPosen Hsu |
Price & Availability of SIR19-315
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |